1. Search
    Last Post
    Replies
    Views
  2. Most likely the RTA is set to monitor the signal...

    Most likely the RTA is set to monitor the signal pre-eq. Alternatively, you might have something soloed, and the RTA is listening to the solo bus. If the monitor settings dictate that channel solo...
  3. On the Core, Setup>Preamps HA Remote:AES50A will...

    On the Core, Setup>Preamps HA Remote:AES50A will send preamp control out to whatever is connected to the Core's AES50-A socket (which will be the Compact if you've followed Paul's connectivity...
  4. It's an ugly solution, but if you've got space in...

    It's an ugly solution, but if you've got space in the FX rack and the insert point isn't used on the sub matrix, you could insert the pitch shifter across the sub matrix and use the pitch shifter's...
  5. 3 Days Ago
    1
    64

    Works fine, but a couple of caveats: Can't work...

    Works fine, but a couple of caveats:
    Can't work stereo (although the returns are stereo, the sends are only mono, and cannot be linked, unlike the X32.)
    No compression\limiting\inserts (unlike the...
  6. 4 Days Ago
    5
    99

    Sort of. Signals from preamps are...

    Sort of.

    Signals from preamps are automatically routed to the USB socket anyway (you can confirm this by going to the "In\Out" button in the top right of the app and accessing the "USB sends"...
  7. 4 Days Ago
    5
    99

    Check the output of each track in Logic. It...

    Check the output of each track in Logic. It should be that track1 outputs to ch1, track2 to ch2, track3 to ch3 etc. I have a feeling that by default all track outputs will just be to logic's master...
  8. 5 Days Ago
    2
    54

    It could be several things. If you can upload...

    It could be several things. If you can upload the scene file, confirm to which socket on the console the S16 is connected (AES50 A\B) and confirm which mode the S16 is in, we should be able to...
  9. 6 Days Ago
    2
    125

    A brief explanation of the routing table:...

    A brief explanation of the routing table:
    /shameless self plug.

    Bottom line is that "Local X-Y" refers to the signals at the console's Local preamps. If you've set outputs on the...
  10. 6 Days Ago
    8
    195

    Perhaps Setup>Card is set to do 16x16... ...

    Perhaps Setup>Card is set to do 16x16...

    Depending on how monitors\foh mixes and outputs work, it could be possible to run S16>monitors>FOH, transfer all the signals from preamps to the FOH...
  11. 1 Week Ago
    2
    119

    Each bus has it's own dedicated 6-band peq\31...

    Each bus has it's own dedicated 6-band peq\31 band geq\teq (as well as insert point across which you can insert one of the regular geq\teqs or boutique peqs from the FX rack.) Whatever you do with...
  12. Ethernet Connectivity (not necessarily how I'd do...

    Ethernet Connectivity (not necessarily how I'd do it, but from what I've gleaned from your post.)
    DL32(A)>MC32R(A), M32R(B)>M32C(A)

    On The M32R
    Settings>Global
    Synchronization: Internal (M32R...
  13. Thanks. I must have missed that post.

    Thanks. I must have missed that post.
  14. What is "auto mute?"

    What is "auto mute?"
  15. Assuming Rack(A)>S16(A) Setup>Card 32x32 ...

    Assuming Rack(A)>S16(A)

    Setup>Card
    32x32

    Routing>CardOut
    Output1-16: AES50A 1-16
    Output17-32: Local 1-16
    ^That gets signals from all your preamps recorded to the SD card.
  16. 1 Week Ago
    6
    129

    Dedicated TRS balanced outputs for the solo bus...

    Dedicated TRS balanced outputs for the solo bus (basically what you were trying to do with output11+12 on the DL16. Whatever is in the solo bus (eg when you hit the solo button on a channel, but you...
  17. Monitor is afl, recording afl... is the lr fader...

    Monitor is afl, recording afl... is the lr fader actually up and un-muted?
  18. 1 Week Ago
    42
    813

    What firmware are you running? Depending on how...

    What firmware are you running? Depending on how long the unit was sitting on the shelf before you bought it, it may have been shipped to you with an old firmware. There have been a few enhancements...
  19. 2 Weeks Ago
    19
    383

    The X-Y was just shorthand for number variables. ...

    The X-Y was just shorthand for number variables. 1-8, 9-16, 17-24, 25-32 (and in the case of AES50 A\B, 33-40 and 41-48.)
  20. 2 Weeks Ago
    19
    383

    A brief explanation on the routing table: ...

    A brief explanation on the routing table:

    Selection options (check boxes, not tabs) in the routing table:

    Local X-Y: Signals direct from local preamps on the rear of the console. Only...
  21. 2 Weeks Ago
    19
    383

    Fair enough. My apologies, I didn't read through...

    Fair enough. My apologies, I didn't read through all the thread. The Buses (and matrices) all have their own dedicated 6-band peqs, and they also have their own insert points if you want to insert...
  22. 2 Weeks Ago
    19
    383

    Oh. Yes, the aux in remap will burn 2 of your...

    Oh. Yes, the aux in remap will burn 2 of your aux in sockets (though you'll be able to still use aux3-6 for keys,) and yes, this is how to get 2-track (or 4-track, or 6-track depending on how many...
  23. 2 Weeks Ago
    19
    383

    If it's only 2 tracks out of the DAW you need for...

    If it's only 2 tracks out of the DAW you need for monitoring, then use the AuxIn Remap feature (Routing>Inputs, AuxIn Remap: Card1-2.) This will get outputs1+2 from the DAW (which is normally the...
  24. 2 Weeks Ago
    10
    307

    Yep. Routing>Aux out. Set an output to M\C,...

    Yep. Routing>Aux out. Set an output to M\C, Post fader.
    Keep in mind that on the Rack the TRS outputs have -5dB less headroom compared to the XLR outs (16dBu vs 21 dBu.) The M32 consoles are far...
  25. 2 Weeks Ago
    10
    307

    Use only 5 monitors? Routing>Aux out and run the...

    Use only 5 monitors?
    Routing>Aux out and run the subs off TRS?
    Use a stagebox connected via AES50 and run the subs of that?
  26. 2 Weeks Ago
    2
    83

    Block diagram....

    Block diagram.

    Typically post-eq is after the channel's eq, but before the channel's compressor. Pre-fader is post the channel's compressor, so changing it should have either included or excluded...