1. Search
    Last Post
    Replies
    Views
  2. Iíll see if I can replicate this when Iím back...

    Iíll see if I can replicate this when Iím back home...
  3. 1 Day Ago
    26
    334

    Digico sd12: max +22dBu Soundcraft vi7000: max...

    Digico sd12: max +22dBu
    Soundcraft vi7000: max +28dBu
    Avid stage 16: max +32dBu (with pad).

    None of them can handle +43dBu... Most pro mixers hoovers around +24dBu of maximum input level, give...
  4. 1 Day Ago
    26
    334

    If you knew of how many user requests Paul and...

    If you knew of how many user requests Paul and myself have been able to push as updates to the x32 and its apps over the years you wouldnít say things like that.

    I actually feel quite offended by...
  5. 1 Day Ago
    2
    26

    As far as I understand it the controls sends...

    As far as I understand it the controls sends fixed CCís (or note on/off depending on in what mode you are operating in) and they are not reassignable.

    Only mcu mode allows you to reassign buttons...
  6. 1 Day Ago
    26
    334

    Btw, since adding a pad of 20dB in software would...

    Btw, since adding a pad of 20dB in software would be equivalent to a maximum of a +43dB input signal, this is the same as 110vac.

    Iíll bet that if you were to put 110vac directly on your xlr...
  7. 1 Day Ago
    26
    334

    The opamps and protective diodes that is before...

    The opamps and protective diodes that is before the opamps) are clamped to +/-15v according to the schematics you linked to. You will clip the signal before it hits the opamp. Even then, the opamp...
  8. For testing, pull out the option card. Can you...

    For testing, pull out the option card.

    Can you see any text flash on the lcd before rebooting?
  9. Have a look at this document ...

    Have a look at this document

    https://www.sweetwater.com/sweetcare/articles/resolving-audio-interface-issues-on-mac
  10. Did this work prior to the 10.13.6 macos update?...

    Did this work prior to the 10.13.6 macos update? Iím assuming that you are on the latest update...
  11. I usually setup subs on aux and they are usually...

    I usually setup subs on aux and they are usually haystacked so I donít perceive any real issues with this setup in the crossover region.

    I also try to avoid splitting the subs and put them near...
  12. 6 Days Ago
    4
    94

    You can use audacity with asio but you need to...

    You can use audacity with asio but you need to perform some work yourself.

    https://wiki.audacityteam.org/wiki/ASIO_Audio_Interface
  13. There is no ĒproperĒ way to find what is causing...

    There is no ĒproperĒ way to find what is causing feedback other than pulling faders.

    However, proper feedback hunting before the show starts is essential so that you may ring out your system not...
  14. That sound like dirt has entered into the fader...

    That sound like dirt has entered into the fader slot. Unless you have the proper experience to clean the faders Iíd recommend taking it to a service center to get them either cleaned out or replaced....
  15. I would NOT use the 1/8Ē-xlr cable adapter...

    I would NOT use the 1/8Ē-xlr cable adapter because of the concerns that you mention.

    Phantom power will travel to the headphone port on your computer and while some computers will happily ignore...
  16. As I understood it v1.xx is reserved for the...

    As I understood it v1.xx is reserved for the previous hardware and v2.xx is reserved for the current hardware so if you have a mixed hardware of iq-speakers you should probably put a sticker on it to...
  17. 1 Week Ago
    9
    354

    Yes, it is a dumb terminal. Xctl is based on...

    Yes, it is a dumb terminal. Xctl is based on mackie mcu, not osc.
  18. 1 Week Ago
    9
    354

    The x-touch does not need to be updated for this...

    The x-touch does not need to be updated for this feature as any change of functionallity in regards of the x/m mixers actually needs to happen on the mixer firmware and not the x-touch firmware.
  19. The v2.x firmware is for the revised hardware on...

    The v2.x firmware is for the revised hardware on the iq-platform and will not load on the original iq-series of speakers.

    To the user there should be no difference between the different hardware...
  20. Just for testing, try to set those sliders to...

    Just for testing, try to set those sliders to their minimum position before recalling that patch.

    It looks like the dm detects movements in those sliders for some reason...
  21. Iíll see what I can find.

    Iíll see what I can find.
  22. 1 Week Ago
    42
    813

    Some daw like studio one frame rate (6Hz) for...

    Some daw like studio one frame rate (6Hz) for external controllers is quite low and can make the xtouch sound more than usual since the faders will move in steps rather than more smoothly.

    Here is...
  23. 1 Week Ago
    1
    92

    There exist no bitmap control of the xtouch.

    There exist no bitmap control of the xtouch.
  24. Btw, was it you who bought the Katana? I got one...

    Btw, was it you who bought the Katana? I got one a couple of weeks ago...
  25. Cool! I guess that you didnít add any reverb...

    Cool!

    I guess that you didnít add any reverb from the mixer :p
  26. You need to pull out your soldering iron and...

    You need to pull out your soldering iron and replace those leds :cool:

    Unfortunetly only the scribbles can change color, not the buttons...